Why IPO Applications Get Rejected — And How to Avoid It
A rejected application is not in the draw at all. Here are the errors that cause technical rejection, in the order they actually occur, and the checks that eliminate each one.
Investors who miss out on an oversubscribed IPO usually assume they lost the draw. A meaningful proportion never entered it.
A technical rejection removes an application before allotment is run. It is not a reduced chance — the application is simply not there. And unlike losing a lottery, every cause of it is preventable.
The unapproved mandate
By a wide margin the most common failure. The bid reaches the exchange, the UPI mandate is sent, and nobody approves it.
The request often arrives without a visible notification. It sits in the pending mandates section of the UPI app, and if it is still there when the issue closes, the application is unfunded and rejected.
The fix: apply early, open the app immediately, and go looking for the request rather than waiting for it. Then confirm a lien has actually appeared on your bank balance.
Insufficient balance at the block
Approving a mandate with less than the full amount free means the block fails. The application stays on the exchange, unfunded.
The amount required is the cap price times the lot size — not the price you expect to pay. And it must be a free balance; an overdraft or sanctioned limit does not count.
The fix: keep the full blocked amount untouched from application until allotment day.
Wrong DP ID or client ID
The registrar matches your application against the depository record. A mismatch means the shares cannot be delivered, so the application is rejected.
The formats differ between depositories, which is where the errors come from. A CDSL account is a single sixteen-digit number. An NSDL account begins with IN followed by fourteen characters.
The fix: copy the details from your client master report rather than typing them from memory. The CMR is issued by your depository participant and is the authoritative record.
PAN mismatch
The PAN on the application must be the PAN registered against the demat account, exactly. A dormant, inactive or frozen demat account will also fail.
The fix: check the PAN on your CMR, and check the account is active — particularly if you have not used it in a while or have an incomplete re-KYC.
Multiple applications under one PAN
Only one application per PAN per category is permitted. Deduplication runs on PAN, and where two are found, both are rejected — including the one that would have been allotted.
This catches people who apply through two brokers, or who apply and then apply again after a failed mandate without cancelling the first.
The fix: one application per PAN. Family members with their own PANs and their own demat accounts may each apply, and that is the legitimate way to increase entries. If a mandate fails, confirm the original bid was cancelled before submitting a fresh one.
Third-party funding
The bank account or UPI handle used to block funds must belong to the first applicant. Funding a spouse’s or an adult child’s application from your own account makes it a third-party application.
Registrars check against bank records, and these are rejected even when allotment would otherwise have been made.
The fix: every applicant funds from an account in their own name.
Bidding below the issue price
Not a technical rejection, but the outcome is identical. If you name a price and the issue prices above it, your bid is excluded from allotment.
The fix: retail investors should bid at cut-off, every time.
Wrong category or invalid quantity
An application above two lakh rupees is not a large retail application — it belongs in the non-institutional category, and if it is submitted as retail the categorisation is corrected or the application is rejected.
Quantities that are not whole multiples of the lot size are invalid.
The fix: stay under two lakh rupees to remain retail, and apply in whole lots.
A pre-submission checklist
- PAN matches the demat account exactly
- DP ID and client ID copied from the client master report
- Demat account active, KYC current
- Funding account and UPI handle in the first applicant’s own name
- Full cap-price amount free in the account
- One application only, under this PAN, in this issue
- Whole number of lots, within the category limit
- Cut-off ticked
- Mandate approved the same day, and the lien visible on the balance
For anyone applying on behalf of others
Broking desks submitting hundreds of applications hit these failures at scale, and the causes are the same. The difference is that the errors are systematic — a stale client master file will produce the same DP ID mismatch across every affected client at once.
Validating client data against current depository records before an issue opens, rather than discovering the problem on allotment day, is the whole game at that scale.
Frequently asked questions
Will I be told if my application was rejected?
Not proactively in most cases. The allotment status on the registrar's portal will show the application as rejected or simply not allotted. The blocked amount is released either way, so the money comes back — you just never had a chance at the shares.
My spouse and I applied from the same bank account. Is that a problem?
Yes. The funding account must belong to the first applicant on each application. Two applications from one account make one of them a third-party application, which is liable to rejection.
I applied twice by mistake under the same PAN. Which one counts?
Neither. Deduplication runs on PAN, and where multiple applications are found in the same category, all of them are rejected — including the one that would otherwise have been allotted.
Can a rejected application be fixed?
Only while the issue is still open. A failed mandate can be retried and a bid can be re-entered before the close. After the issue shuts, nothing can be corrected.